RND to Launch Two 500 Series Modules at 2013 NAMM Show
January 17, 2013
Wimberley, TX — January 2013 — For the 2013 NAMM show, Rupert Neve Designs is announcing two new 500 Series modules: the 511 Mic Pre with Silk, and the 542 True Tape Emulator with Texture. As two of the only 500 Series modules actually designed by Mr. Rupert Neve, the 511 and 542 combine the classic tone and versatility expected from a Rupert Neve design with the form factor and value of the 500 Series format.
511 Mic Pre with Silk
With a truly legendary preamp and the flexibility of variable Silk/Texture, the 511 provides exceptional sonic performance and flexibility for only $650 (list). Incorporating the pristine preamp circuitry from the 517, the sweepable high-pass filter from the 5012, and the power of a variable Silk circuit derived from the flagship Portico II Channel, the 511 is a Rupert Neve-designed workhorse for any user’s most important tracks.
For company founder and lead designer Rupert Neve, the design process was far more intensive than copying existing designs. “Although creating a functional 500 Series mic pre is relatively simple, designing those modules to equal their non-500 Series counterparts with the current, voltage and space restraints is quite challenging. In creating the 511 we experimented with a number of different transformer and circuit topologies to achieve the same presence and sweetness found in the Portico Series of modules. The result of these efforts is that outside of the slightly lowered headroom, the 511′s performance is nearly indistinguishable from standard Portico Series modules.”
The 511 can be used for either mic or line sources, and pairs perfectly with any ribbon, dynamic, condenser or tube microphone. A polarity reverse switch is available to conquer phase issues when using multiple microphones. The 12 dB/octave swept high-pass filter can be dialed-in to remove rumble with minimal artifacts, and also to control proximity effect in close-mic’d vocals or other sources. To coax more rich harmonic content from the output transformer, the Silk Red mode can be engaged to add more thickness and sparkle in the high end as the Texture level is increased. While a little Silk Red can sound great on nearly any source, it is especially useful on dynamic and ribbon microphones that are inherently lacking in high-frequency energy and excitement.
542 True Tape Emulator with Texture
The second new module, the 542, is a follow-up to the acclaimed Portico 5042 which has a will retail for only $895 list. As such, it delivers a remarkable simulation of classic tape sound through the inclusion of genuine tape drive circuitry while also incorporating a number of new methods for adding analogue color to individual tracks and mixes.
The 542’s “True Tape” emulation circuit provides the nostalgic rounding and compression typically achieved only through the use of tape, and can offset the harshness often found in digital recordings. Unlike digital emulations, the “True Tape” drive circuit works by feeding a tiny magnetic “record head,” which in turn is coupled to a correctly-equalized replay amplifier. As the voltage rises on the “record head,” saturation increases, and a soft-clip circuit engages at higher levels to round off harsh peak transients. The sound of the tape circuit can be further modified with selectable 15 and 30 ipsmodes, providing a “saturation equalization” of sorts, and a pre/post-tape blend control. In addition to the tape circuit, the 542 also includes the variable Silk/Texture circuitry found in the Portico II series of modules (with both much-loved Red and Blue modes), which allows the engineer to fine-tune the harmonic ratio and tonality of the output transformer.
For engineers, the 542 is an intuitive and dynamic tonal control. The non-linear qualities of the “True Tape” head, Soft-Clip and Silk circuits can be combined and tuned by simply adjusting the saturation, blend and texture controls. These effects can help breathe new life into sterile tracks and enhance performances with their dynamic response. For example, a snare drum captured with a dynamic microphone that sounds anemic and “dead” in the high-end could be run through the 542′s tape and Red Silk circuits to simultaneously thicken the low end and sweeten the high end. If the snare is overly dynamic, the saturation knob can push the signal into soft-clip mode, thus reducing transient spikes. Additionally, the blend control can be used to preserve the drum’s natural dynamics and transient content even with more extreme applications of soft-clip and saturation.
Similarly, using two 542s across a mix, the gain staging can be optimized such that the tape circuit provides extra intensity and excitement in the loudest sections before final compression and limiting. Using this technique can help retain a more dynamic feel, even after the dynamics have been reduced, as the instances with the most compression correspond to the instances that have more pleasant harmonic distortion provided by the “True Tape” circuitry.
With the introduction of the 511 and 542 to the Portico 500 Series, which also includes the existing 517 Mic Pre/Compressor/DI and the 543 Mono Compressor, the 500 Series now has four of the most versatile tone controllers and mic preamps available on the market. In a world with numerous imitations, only the Portico 500 Series modules carry on the legacy of tone, quality and craftsmanship synonymous with the Rupert Neve name.
About Rupert Neve Designs:
Founded by Rupert and Evelyn Neve, Rupert Neve Designs is built on passion, experience and a desire to create products embodying the highest musical quality. In continuing his legacy as a pioneer in audio circuit design, Mr. Rupert Neve is currently focusing his talents on creating innovative solutions to the issues facing the modern recording engineer. For further information on Rupert Neve Designs please visit www.rupertneve.com
Portico is a trademark of Rupert Neve Designs, Inc. All other trademarks remain the property of their respective owners.
Company contact: Rupert Neve Designs, PO Box 1969, Wimberley, TX 78676. Tel: (512) 847-3013 Fax: (512) 847-8869 E-mail: firstname.lastname@example.org